|
DS DS/CEN/TS 1071- 10 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 10: Determination of coating thickness by cross sectioning |
|
DS DS/CEN/TS 1071- 11 |
Advanced technical ceramics Methods of test for ceramic coatings Part 11: Determination of internal stress by the Stoney formula |
|
DS DS/CEN/TS 1071- 7 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 7: Determination of hardness and Young´s modulus by instrumented indentation testing |
|
DS DS/CEN/TS 1071- 8 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 8: Rockwell indentation test for evaluation of adhesion |
|
DS DS/CEN/TS 1071- 9 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 9: Determination of fracture strain |
|
DS DS/CEN/TS 1159- 4 |
Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 4: Determination of thermal conductivity |
|
DS DS/CEN/TS 14425- 1 |
Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 1: Guide to test method selection |
|
DS DS/CEN/TS 14425- 3 |
Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 3: Chevron notched beam (CNB) method |
|
DS DS/CEN/TS 14425- 5 |
Advanced technical ceramics - Test methods for determination of fracture toughness of monolithic ceramics - Part 5: Single-edge vee-notch beam (SEVNB) method |
|
DS DS/CEN/TS 820- 5 |
Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 5: Determination of elastic moduli at elevated temperatures |
|
DS DS/CEN/TS 843- 6 |
Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Part 6: Guidance for fractographic investigation |
|
DS DS/CEN/TS 993- 11 |
Dense shaped refractory products - Part 11: Determination of resistance to thermal shock |
|
DS DS/EN 1007- 1 |
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 1: Determination of size content |
|
DS DS/EN 1007- 2 |
Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement - Part 2: Determination of linear density |
|
DS DS/EN 1007- 3 |
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcement - Part 3: Determination of filament diameter and cross-section area |
|
DS DS/EN 1007- 4 |
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 4: Determination of tensile properties of filaments at ambient temperature |
|
DS DS/EN 1007- 5 |
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 5: Determination of distribution of tensile strength and of tensile strain to failure of filaments within a multifilament tow at ambient temperature |
|
DS DS/EN 1036 |
Glass in building - Mirrors from silver-coated float glass for internal use |
|
DS DS/EN 1051- 1 |
Glass in building - Glass blocks and glass pavers - Part 1: Definitions and description |
|
DS DS/EN 1063 |
Glass in building - Security glazing - Testing and classification of resistance against bullet attack |
|
DS DS/EN 1071- 1 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 1: Determination of coating thickness by contact probe filometer |
|
DS DS/EN 1071- 2 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 2: Determination of coating thickness by the crater grinding method |
|
DS DS/EN 1071- 3 |
Advanced technical ceramics Methods of test for ceramic coatings Part 3: Determination of adhesion and other mechanical failure modes by a scratch test |
|
DS DS/EN 1094- 1 |
Insulating refractory products - Part 1: Terminology for ceramic fibre products |
|
DS DS/EN 1094- 2 |
Insulating refractory products - Part 2: Classification of shaped products |
|
DS DS/EN 1094- 3 |
Insulating refractory products - Part 3: Classification of insulating products made from ceramic fibres |
|
DS DS/EN 1094- 4 |
Insulating refractory products - Part 4: Determination of bulk density and true porosity |
|
DS DS/EN 1094- 5 |
Insulating refractory products - Part 5: Determination of cold crushing strength |
|
DS DS/EN 1094- 6 |
Insulating refractory products - Part 6: Determination of permanent change in dimensions of shaped products on heating |
|
DS DS/EN 1096- 1 |
Glass in building - Coated glass - Part 1: Definitions and classification |
|
DS DS/EN 1096- 2 |
Glass in building - Coated glass - Part 2: Requirements and test methods for class of A, B and S coatings |
|
DS DS/EN 1096- 3 |
Glass in building - Coated glass - Part 3: Requirements and test methods for class C and D coatings |
|
DS DS/EN 1096- 4 |
Glass in building - Coated glass - Part 4: Evaluation of conformity/Product standard |
|
DS DS/EN 1159- 1 |
Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 1: Determination of thermal expansion |
|
DS DS/EN 1159- 2 |
Advanced technical ceramics - Ceramic composites - Thermophysical properties - Part 2: Determination of thermal diffusivity |
|
DS DS/EN 1159- 3 |
Advanced technical ceramics - Ceramic composites, thermophysical properties - Part 3: Determination of specific heat capacity |
|
DS DS/EN 12150- 1 |
Glass in building - Thermally toughened soda lime silicate safety glass - Part 1: Definition and description |
|
DS DS/EN 12150- 2 |
Glass in building - Thermally toughened soda lime silicate safety glass - Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 12289 |
Advanced technical ceramics Mechanical properties of ceramic composites at ambient temperature Determination of in-plane shear properties |
|
DS DS/EN 12290 |
Advanced technical ceramics Mechanical properties of ceramic composites at high temperature under inert atmosphere Determination of compression properties |
|
DS DS/EN 12291 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of compression properties |
|
DS DS/EN 12337- 1 |
Glass in building - Chemically strengthened soda lime silicate glass - Part 1: Definition and description |
|
DS DS/EN 12337- 2 |
Glass in building - Chemically strengthened soda lime silicate glass - Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 12475- 4 |
Classification of dense shaped refractory products - Part 4: Special products |
|
DS DS/EN 12600 |
Glass in building - Pendulum test - Impact test method for flat glass |
|
DS DS/EN 12603 |
Glass in building - Procedures for goodness of fit and confidence intervals for Weibull distributed glass strength data |
|
DS DS/EN 12758 |
Glass in building - Glazing and airborne sound insulation - Product descriptions and determination of properties |
|
DS DS/EN 12788 |
Advanced technical ceramics Mechanical properties of ceramic composites at high temperature under inert atmosphere Determination of flexural strength |
|
DS DS/EN 12789 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under air at atmospheric pressure - Determination of flexural strength |
|
DS DS/EN 1288- 1 |
Glass in building - Determination of the bending strength of glass - Part 1: Fundamentals of testing glass |
|
DS DS/EN 1288- 2 |
Glass in building - Determination of the bending strength of glass - Part 2: Coaxial double ring test on flat specimens with large test surface areas |
|
DS DS/EN 1288- 3 |
Glass in building - Determination of the bending strength of glass - Part 3: Test with specimen supported at two points (four point bending) |
|
DS DS/EN 1288- 4 |
Glass in building - Determination of the bending strength of glass - Part 4: Testing of channel shaped glass |
|
DS DS/EN 1288- 5 |
Glass in building - Determination of the bending strength of glass - Part 5: Coaxial double ring test on flat specimens with small test surface areas |
|
DS DS/EN 12898 |
Glass in building - Determination of the emissivity |
|
DS DS/EN 13024- 1 |
Glass in building - Thermally toughened borosilicate safety glass - Part 1: Definition and description |
|
DS DS/EN 13024- 2 |
Glass in building - Thermally toughened borosilicate safety glass - Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 13035- 3 |
Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 3: Cutting machines |
|
DS DS/EN 13035- 4 |
Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 4: Tilting tables |
|
DS DS/EN 13042- 2 |
Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 2: Handling machines for feeding |
|
DS DS/EN 13042- 5 |
Machines and plants for the manufacture, treatment and processing of hollow glass - Safety requirements - Part 5: Presses |
|
DS DS/EN 13367 |
Ceramic machines Safety Transfer platforms and cars |
|
DS DS/EN 13541 |
Glass in building - Security glazing - Testing and classification of resistance against explosion pressure |
|
DS DS/EN 1388- 1 |
Materials and articles in contact with foodstuffs - Silicate surfaces - Part 1: Determination of the release of lead and cadmium from ceramic ware |
|
DS DS/EN 1388- 2 |
Materials and articles in contact with foodstuffs - Silicate surfaces - Part 2: Determination of the release of lead and cadmium from silicate surfaces other than ceramic ware |
|
DS DS/EN 1389 |
Advanced technical ceramics - Ceramic composites - Physical properties - Determination of density and apparent porosity |
|
DS DS/EN 1402- 1 |
Unshaped refractory products - Part 1: Introduction and classification |
|
DS DS/EN 1402- 2 |
Unshaped refractory products - Part 2: Sampling for testing |
|
DS DS/EN 1402- 3 |
Unshaped refractory products - Part 3: Characterization as received |
|
DS DS/EN 1402- 4 |
Unshaped refractory products - Part 4: Determination of consistency of castables |
|
DS DS/EN 1402- 5 |
Unshaped refractory products - Part 5: Preparation and treatment of test pieces |
|
DS DS/EN 1402- 6 |
Unshaped refractory products - Part 6: Measurement of physical properties |
|
DS DS/EN 1402- 7 |
Unshaped refractory materials - Part 7: Tests on pre-formed shapes |
|
DS DS/EN 1402- 8 |
Unshaped refractory produts - Part 8: Determination of complementary properties |
|
DS DS/EN 14178- 1 |
Glass in building - Basic alkaline earth silicate glass - Part 1: Float glass |
|
DS DS/EN 14178- 2 |
Glass in building - Basic alkaline earth silicate glass products - Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 14179- 1 |
Glass in building Heat soaked thermally toughened soda lime silicate safety glass Part 1: Definition and description |
|
DS DS/EN 14179- 2 |
Glass in building Heat soaked thermally toughened soda lime silicate safety glass Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 14321- 1 |
Glass in building Thermally toughened alkaline earth silicate safety glass Part 1: Definition and description |
|
DS DS/EN 14321- 2 |
Glass in building Thermally toughened alkaline earth silicate safety glass Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 14449 |
Glass in building Laminated glass and laminated safety glass Evaluation of conformity/Product standard |
|
DS DS/EN 1595 |
Pressure equipment made from borosilicate glass 3.3 - General rules for design, manufacture and testing |
|
DS DS/EN 1748-1- 1 |
Glass in building - Special basic products - Borosilicate glasses - Part 1- 1: Definition and general physical and mechanical properties |
|
DS DS/EN 1748-1- 2 |
Glass in building - Special basic products - Borosiliacte glasses - Part 1- 2: Evaluation of conformity/Product standard |
|
DS DS/EN 1748-2- 1 |
Glass in building - Special basic products - Glass ceramics - Part 2-1: Definitions and general physical and mechanical properties |
|
DS DS/EN 1748-2- 2 |
Glass in building - Special basic products - Part 2-2: Glass ceramics - Evaluation of conformity/Product standard |
|
DS DS/EN 1863- 1 |
Glass in building - Heat strengthened soda lime silicate glass - Part 1: Definition and description |
|
DS DS/EN 1863- 2 |
Glass in building - Heat strengthened soda lime silicate glass - Part 2: Evaluation of conformity/Product standard |
|
DS DS/EN 356 |
Glass in building - Security glazing - Testing and classification of resistance against manual attack |
|
DS DS/EN 357 |
Glass in building - Fire resistant glazed elements with transparent or translucent glass products - Classification of fire resistance |
|
DS DS/EN 410 |
Glass in building - Determination of luminous and solar characteristics of glazing |
|
DS DS/EN 572- 1 |
Glass in building - Basic soda lime silicate glass products - Part 1: Definitions and general physical and mechanical properties |
|
DS DS/EN 572- 2 |
Glass in building - Basic soda lime silicate glass products - Part 2: Float glass |
|
DS DS/EN 572- 3 |
Glass in building - Basic soda lime silicate glass products - Part 3: Polished wire glass |
|
DS DS/EN 572- 4 |
Glass in building - Basic soda lime silicate glass products - Part 4: Drawn sheet glass |
|
DS DS/EN 572- 5 |
Glass in building - Basic soda lime silicate glass products - Part 5: Patterned glass |
|
DS DS/EN 572- 6 |
Glass in building - Basic soda lime silicate glass products - Part 6: Wired patterned glass |
|
DS DS/EN 572- 7 |
Glass in building - Basic soda lime silicate glass products - Part 7: Wired or unwired channel shaped glass |
|
DS DS/EN 572- 8 |
Glass in building - Basic soda lime silicate glass products - Part 8: Supplied and final cut sizes |
|
DS DS/EN 572- 9 |
Glass in buildings - Basic soda lime silicate glass products - Part 9: Evaluation of conformity/Product standard |
|
DS DS/EN 60519- 21 |
Safety in electroheat installations - Part 21: Particular requirements for resistance heating equipment - Heating and melting glass equipment |
|
DS DS/EN 623- 1 |
Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 1: Determination of the presence of defects by dye penetration tests |
|
DS DS/EN 623- 2 |
Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 2: Determination of density and porosity |
|
DS DS/EN 623- 3 |
Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 3: Determination of grain size and size distribution (characterized by the Linear Intercept Method) |
|
DS DS/EN 623- 4 |
Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 4: Determination of surface roughness |
|
DS DS/EN 658- 1 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 1: Determination of tensile properties |
|
DS DS/EN 658- 2 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 2: Determination of compression properties |
|
DS DS/EN 658- 3 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 3: Determination of flexural strength |
|
DS DS/EN 658- 4 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 4: Determination of interlaminar shear strength by compression loading of notched test specimens |
|
DS DS/EN 658- 5 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 5: Determination of interlaminar shear strength by short span bend test (three points) |
|
DS DS/EN 673 |
Glass in building - Determination of thermal transmittance (U-value) - Calculation method |
|
DS DS/EN 673/A1 |
Glass in building - Determination of thermal transmittance (U-value) - Calculation method-(AMENDS DS/EN 673) |
|
DS DS/EN 673/A2 |
Glass in building - Determination of thermal transmittance (U-value) - Calculation method-(AMENDS DS/EN 673) |
|
DS DS/EN 674 |
Glass in building - Determination of thermal transmittance (U-value) - Guarded hot plate method |
|
DS DS/EN 675 |
Glass in building - Determination of thermal transmittance (U-value) - Heat flow meter method |
|
DS DS/EN 725- 1 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 1: Determination of impurities in alumina |
|
DS DS/EN 725- 10 |
Advanced technical ceramics - Methods of test for ceramic powders Part 10: Determination of compaction properties |
|
DS DS/EN 725- 12 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 12: Chemical analysis of zirconia |
|
DS DS/EN 725- 3 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content of non-oxides by thermal extraction with a carrier gas |
|
DS DS/EN 725- 5 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 5: Determination of the particle size distribution |
|
DS DS/EN 725- 6 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 6: Determination of the specific surface area |
|
DS DS/EN 725- 7 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 7: Determination of the absolute density |
|
DS DS/EN 725- 8 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 8: Determination of tapped bulk density |
|
DS DS/EN 725- 9 |
Advanced technical ceramics - Methods of test for ceramic powders Part 9: Determination of untamped bulk density |
|
DS DS/EN 820- 1 |
Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 1: Determination of flexural strength at elevated temperatures |
|
DS DS/EN 820- 2 |
Advanced technical ceramics - Methods of testing monolithic ceramics - Thermo-mechanical properties - Part 2: Determination of self-loaded deformation |
|
DS DS/EN 820- 3 |
Advanced technical ceramics - Methods of testing monolithic ceramics - Thermomechanical properties - Part 3: Determination of resistance to thermal shock by water quenching |
|
DS DS/EN 821- 1 |
Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Part 1: Determination of thermal expansion |
|
DS DS/EN 821- 3 |
Advanced technical ceramics Monolithic ceramics - Thermo-physical properties Part 3: Determination of specific heat capacity |
|
DS DS/EN 843- 1 |
Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Part 1: Determination of flexural strength |
|
DS DS/EN 843- 3 |
Advanced technical ceramics Mechanical properties of monolithic ceramics at room temperature Part 3: Determination of subcritical crack growth parameters from constant stressing rate flexural strength tests |
|
DS DS/EN 843- 4 |
Advanced technical ceramics Mechanical properties of monolithic ceramics at room temperature Part 4: Vickers, Knoop and Rockwell superficial hardness |
|
DS DS/EN 955- 2 |
Chemical analysis of refractory products - Part 2: Products containing silica and/or alumina (wet method) |
|
DS DS/EN 993- 1 |
Methods of test for dense shaped refractory products - Part 1: Determination of bulk density, apparent porosity and true porosity |
|
DS DS/EN 993- 10 |
Methods of test for dense shaped refractory products - Part 10: Determination of permanent change in dimensions on heating |
|
DS DS/EN 993- 12 |
Methods of test for dense shaped refractory products - Part 12: Determination of pyrometric cone equivalent (refractoriness) |
|
DS DS/EN 993- 13 |
Methods of test for dense shaped refractory products - Part 13: Specification for pyrometric reference cones for laboratory use |
|
DS DS/EN 993- 14 |
Methods of testing dense shaped refractory products - Part 14: Determination of thermal conductivity by the hot-wire (cross-array) method |
|
DS DS/EN 993- 15 |
Methods of test for dense shaped refractory products Determination of thermal conductivity by the hot-wire (parallel) method |
|
DS DS/EN 993- 16 |
Dense shaped refractory products - Methods of test - Part 16: Determination of resistance to sulphuric acid |
|
DS DS/EN 993- 17 |
Methods of test for dense shaped refractory products - Part 17: Determination of bulk density of granular materials by the mercury method with vacuum |
|
DS DS/EN 993- 18 |
Methods of test for dense shaped refractory products - Part 18: Determination of bulk density of granular materials by the water method with vacuum |
|
DS DS/EN 993- 19 |
Methods of test for dense shaped refractory products - Part 19: Determination of thermal expansion by a differential method |
|
DS DS/EN 993- 2 |
Methods of test for dense shaped refractory products - Part 2: Determination of true density |
|
DS DS/EN 993- 2/A1 |
Methods of test for dense shaped refractory products - Part 2: Determination of true density-(AMENDS DS/EN 993-2) |
|
DS DS/EN 993- 20 |
Methods of test for dense shaped refractory products - Part 20: Determination of resistance to abrasion at ambient temperature |
|
DS DS/EN 993- 3 |
Methods of test for dense shaped refractory products - Part 3: Test methods for carbon-containing refractories |
|
DS DS/EN 993- 4 |
Methods of test for dense shaped refractory products - Part 4: Determination of permeability to gases |
|
DS DS/EN 993- 6 |
Methods of test for dense shaped refractory products - Part 6: Determination of modulus of rupture at ambient temperature |
|
DS DS/EN 993- 7 |
Methods of test for dense shaped refractory products - Part 7: Determination of modulus of rupture at elevated temperatures |
|
DS DS/EN 993- 8 |
Methods of testing dense shaped refractory products - Part 8: Determination of refractoriness-under-load |
|
DS DS/EN 993- 9 |
Methods of testing dense shaped refractory products - Part 9: Determination of creep in compression |
|
DS DS/EN ISO 10081- 1 |
Classification of dense shaped refractory products Part 1: Alumina- silica |
|
DS DS/EN ISO 10081- 2 |
Classification of dense shaped refractory products Part 2: Basic products containing less than 7 % residual carbon-(Superseded DS/EN 12475- 2:1998) |
|
DS DS/EN ISO 10081- 3 |
Classification of dense shaped refractory products Part 3: Basic products containing from 7 % to 50 % residual carbon |
|
DS DS/EN ISO 12543- 1 |
Glass in building - Laminated glass and laminated safety glass - Part 1: Definitions and description of component parts |
|
DS DS/EN ISO 12543- 2 |
Glass in building - Laminated glass and laminated safety glass - Part 2: Laminated safety glass |
|
DS DS/EN ISO 12543- 3 |
Glass in building - Laminated glass and laminated safety glass - Part 3: Laminated glass |
|
DS DS/EN ISO 12543- 4 |
Glass in building - Laminated glass and laminated safety glass - Part 4: Test methods for durability |
|
DS DS/EN ISO 12543- 5 |
Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and edge finishing |
|
DS DS/EN ISO 12543- 6 |
Glass in building - Laminated glass and laminated safety glass - Part 6: Appearance |
|
DS DS/EN ISO 12676 |
Refractory products - Determination of resistance to carbon monoxide |
|
DS DS/EN ISO 12677 |
Chemical analysis of refractory products by XRF - Fused cast bead method |
|
DS DS/EN ISO 14438 |
Glass in building - Determination of energy balance value - Calculation method |
|
DS DS/EN ISO 15732 |
Fine ceramics (advanced ceramics, advanced technical ceramics) Test method for fracture toughness of monolithic ceramics at room temperature by single edge precracked beam (SEPB) method |
|
DS DS/EN ISO 18756 |
Fine ceramics (advanced ceramics, advanced technical ceramics) Determination of fracture toughness of monolithic ceramics at room temperature by the surface crack in flexure (SCF) method |
|
DS DS/ENV 1006 |
Advanced technical ceramics - Monolithic ceramics - Guidance on the selection of test pieces for the evaluation of properties |
|
DS DS/ENV 1007- 6 |
Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 6: Determination of tensile proporties of filament at high temperature |
|
DS DS/ENV 1071- 3 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 3: Determination of adhesion by a scratch test |
|
DS DS/ENV 1071- 4 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 4: Determination of chemical composition |
|
DS DS/ENV 1071- 5 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 5: Determination of porosity |
|
DS DS/ENV 1071- 6 |
Advanced technical ceramics - Methods of test for ceramic coatings - Part 6: Determination of the abrasion resistance of coatings by a micro-abrasion wear test |
|
DS DS/ENV 1094- 7 |
Insulating refractory products - Part 7: Methods of test for ceramic fibre products |
|
DS DS/ENV 12212 |
Advanced technical ceramics - Unified method for classification |
|
DS DS/ENV 12788 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of flexural strength |
|
DS DS/ENV 12923- 1 |
Advanced technical ceramics - Monolithic ceramics - Part 1: General practice for undertaking corrosion tests |
|
DS DS/ENV 12923- 2 |
Advanced technical ceramics - Monolithic ceramics - Part 2: Oxidation test |
|
DS DS/ENV 13233 |
Advanced technical ceramics - Ceramic composites - Notations and symbols |
|
DS DS/ENV 13234 |
Advanced technical ceramics - Ceramic composites - Mechanical properties at ambient temperature - Evaluation of the resistance to crack propagation by the notch sensitivity testing |
|
DS DS/ENV 13235 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of creep behaviour |
|
DS DS/ENV 14186 |
Advanced technical ceramics - Ceramic composites - Mechanical properties at room temperature, determination of elastic properties by an ultrasonic technique |
|
DS DS/ENV 14226 |
Advanced technical ceramics - Test methods for ceramic powders - Determination of calcium, magnesium, iron and aluminium in silicon nitride by using flame atomic absorption spectroscopy (FAAS) or inductively coupled plasma atomic emission spectroscopy (IC |
|
DS DS/ENV 14232 |
Advanced technical ceramics - Terms, definitions and abbreviations |
|
DS DS/ENV 14273 |
Advanced technical ceramics - Ceramic powders - Determination of crystalline phases in zirconia |
|
DS DS/ENV 14312 |
Advanced technical ceramics - Ceramic powders - Determination of flowability behaviour of ceramic granules |
|
DS DS/ENV 1892 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of tensile properties |
|
DS DS/ENV 1893 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmospheric pressure - Determination of tensile properties |
|
DS DS/ENV 1894 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature under inert atmosphere - Determination of shear strength by compression loading of notched specimens |
|
DS DS/ENV 623- 5 |
Advanced technical ceramics - Monolithic ceramics - General and textural properties - Part 5: Determination of phase volume fraction by evaluation of micrographics |
|
DS DS/ENV 658- 6 |
Advanced technical ceramics - Mechanical properties of ceramic composites at room temperature - Part 6: Determination of shear strength by double-punch shearing |
|
DS DS/ENV 725- 11 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 11: Determination of the densification on natural sintering |
|
DS DS/ENV 725- 2 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 2: Determination of impurities in barium titanate |
|
DS DS/ENV 725- 4 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 3: Determination of the oxygen content in aluminium nitride by XRF analysis |
|
DS DS/ENV 820- 4 |
Advanced technical ceramics - Monolithic ceramics - Thermomechanical properties - Part 4: Determination of flexural creep deformation at elevated temperature |
|
DS DS/ENV 821- 3 |
Advanced technical ceramics - Monolithic ceramics - Thermo-physical properties - Part 3: Determination of specific heat capacity |
|
DS DS/ENV 843- 2 |
Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Part 2: Determination of elastic moduli |
|
DS DS/ENV 843- 4 |
Advanced technical ceramics - Monolithic ceramics - Mechanical properties at room temperature - Part 4: Vickers, Knoop and Rockwell Superficial hardness tests |
|
DS DS/ENV 843- 5 |
Advanced technical ceramics - Monolithic ceramics - Mechanical tests at room temperature - Part 5: Statistical analysis |
|
DS DS/ENV 955- 4 |
Chemical analysis of refractory products - Part 4: Products containing silica and/or alumina (Analysis by Flame Atomic Absorption Spectrometry (FAAS) and Inductively Coupled Plasma Atomic Emission Spectrography (ICP)) |
|
DS DS/INF 119 |
Guidelines for choice and use of safety glass - Personal safety |