|
DS DS/CEN ISO/TS 21432 |
Non-destructive testing Standards test method for determining residual stresses by neutron diffraction |
|
DS DS/CEN/CR 13935 |
Non-destructive testing - Generic NDE data format model |
|
DS DS/CEN/TR 14748 |
Non-destructive testing - Methodology for qualification of non- destructive tests |
|
DS DS/CEN/TR 15134 |
Non-destructive testing Automated ultrasonic examination Selection and application of systems |
|
DS DS/CEN/TS 15053 |
Non-destructive testing Recommendations for discontinuities-types in test specimens for examination |
|
DS DS/EN 12084 |
Non destructive testing - Eddy current testing - General principles and guidelines |
|
DS DS/EN 12084/A1 |
Non destructive testing - Eddy current testing - General principles and guidelines-(AMENDS DS/EN 12084) |
|
DS DS/EN 12223 |
Non-destructive testing - Ultrasonic examination - Specification for calibration block No. 1 |
|
DS DS/EN 12543- 1 |
Non-destructive testing - Characteristics of focal spots in industrial X-ray systems for use in non-destructive testing - Part 1: Scanning method |
|
DS DS/EN 12543- 2 |
Non-destructive testing - Characteristics of focal spots in industrial X-ray systems for use in non-destructive testing - Part 2: Pinhole camera radiographic method |
|
DS DS/EN 12543- 3 |
Non-destructive testing - Characteristics of focal spots in industrial X-ray systems for use in non-destructive testing - Part 3: Slit camera radiographic method |
|
DS DS/EN 12543- 4 |
Non-destructive testing - Characteristics of focal spots in industrial X-ray systems for use in non-destructive testing - Part 4: Edge method |
|
DS DS/EN 12543- 5 |
Non-destructive testing - Characteristics of focal spot in industrial X-ray systems for use in non-destructive testing - Part 5: Measurement of the effective focal spot size of mini and micro focus X-ray tubes |
|
DS DS/EN 12544- 1 |
Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 1: Voltage divider method |
|
DS DS/EN 12544- 2 |
Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 2: Constancy check by the thick filter method |
|
DS DS/EN 12544- 3 |
Non-destructive testing - Measurement and evaluation of the X-ray tube voltage - Part 3: Spectrometric method |
|
DS DS/EN 12668- 1 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments |
|
DS DS/EN 12668- 1/A1 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 1: Instruments-(AMENDS DS/EN 12668-1) |
|
DS DS/EN 12668- 2 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes |
|
DS DS/EN 12668- 2/A1 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 2: Probes-(AMENDS DS/EN 12668-2) |
|
DS DS/EN 12668- 3 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment |
|
DS DS/EN 12668- 3/A1 |
Non-destructive testing - Characterization and verification of ultrasonic examination equipment - Part 3: Combined equipment-(AMENDS DS/EN 12668-3) |
|
DS DS/EN 12679 |
Non-destructive testing - Determination of the size of industrial radiographic sources - Radiographic method |
|
DS DS/EN 13018 |
Non-destructive testing - Visual testing - General principles |
|
DS DS/EN 13018/A1 |
Non-destructive testing - Visual testing - General principles- (AMENDS DS/EN 13018) |
|
DS DS/EN 13068- 1 |
Non-destructive testing - Radioscopic testing - Part 1: Quantitative measurement of imaging properties |
|
DS DS/EN 13068- 2 |
Non-destructive testing - Radioscopic testing - Part 2: Qualitative control and long term stability of imaging devices |
|
DS DS/EN 13068- 3 |
Non-destructive testing - Radioscopic testing - Part 3: General principles of radioscopic testing of metallic materials by X- and gamma rays |
|
DS DS/EN 13184 |
Non-destructive testing - Leak testing - Pressure change method |
|
DS DS/EN 13184/A1 |
Non-destructive testing - Leak testing - Pressure change method- (AMENDS DS/EN 13184) |
|
DS DS/EN 13185 |
Non-destructive testing - Leak test - Tracer gas method |
|
DS DS/EN 13185/A1 |
Non-destructive testing - Leak testing - Tracer gas method- (AMENDS DS/EN 13185) |
|
DS DS/EN 13192 |
Non destructive testing - Leak testing - Calibration of reference leaks for gases |
|
DS DS/EN 1330- 1 |
Nondestructive testing - Terminology - Part 1: List of general terms |
|
DS DS/EN 1330- 10 |
Non-destructive testing - Terminology - Part 10: Terms used in visual testing |
|
DS DS/EN 1330- 2 |
Non-destructive testing - Terminology - Part 2: Terms common to the non-destructive testing methods |
|
DS DS/EN 1330- 3 |
Non-destructive testing - Terminology - Part 3: Terms used in industrial radiographic testing |
|
DS DS/EN 1330- 4 |
Non destructive testing - Terminology - Part 4: Terms used in ultrasonic testing |
|
DS DS/EN 1330- 5 |
Non-destructive testing - Terminology - Part 5: Terms used in Eddy Current testing |
|
DS DS/EN 1330- 8 |
Non-destructive testing - Terminology - Part 8: Terms used in leak tightness testing |
|
DS DS/EN 1330- 9 |
Non-destructive testing - Terminology - Part 9: Terms used in acoustic emission testing |
|
DS DS/EN 13477- 1 |
Non-destructive testing - Acoustic emission - Equipment characterisation - Part 1: Equipment description |
|
DS DS/EN 13477- 2 |
Non-destructive testing - Acoustic emission - Equipment characterisation - Part 2: Verification of operating characteristic |
|
DS DS/EN 13554 |
Non-destructive testing - Acoustic emission - General principles |
|
DS DS/EN 13625 |
Non-destructive testing - Leak test - Guide to the selection of instrumentation for the measurement of gas leakage |
|
DS DS/EN 13860- 1 |
Non-destructive testing - Eddy current examination - Equipment characteristics and verification - Part 1: Instrument characteristics and verification |
|
DS DS/EN 13860- 2 |
Non-destructive testing - Eddy current examination - Equipment characteristics and verification - Part 2: Probe characteristics and verification |
|
DS DS/EN 13860- 3 |
Non-destructive testing - Eddy current examination - Equipment characteristics and verification - Part 3: System characteristics and verification |
|
DS DS/EN 13925- 1 |
Non-destructive testing - X-ray diffraction from polycrystalline and amorphous material - Part 1: General principles |
|
DS DS/EN 13925- 2 |
Non-destructive testing - X-ray diffraction from polycrystalline and amorphous materials - Part 2: Procedures |
|
DS DS/EN 13927 |
Non-destructive testing - Visual testing - Equipment |
|
DS DS/EN 14096- 1 |
Non-destructive testing - Qualification of radiographic film digitisation systems - Part 1: Definitions, quantitative measurements of image quality parameters, standard reference film and qualitative control |
|
DS DS/EN 14096- 2 |
Non-destructive testing - Qualification of radiographic film digitisation systems - Part 2: Minimum requirements |
|
DS DS/EN 14127 |
Non-destructive testing - Ultrasonic thickness measurement |
|
DS DS/EN 14584 |
Non-destructive testing Acoustic emission Examination of metallic pressure equipment during proof testing Planar location of AE sources |
|
DS DS/EN 14784- 1 |
Non-destructive testing Industrial computed radiography with storage phosphor imaging plates Part 1: Classification of systems |
|
DS DS/EN 14784- 2 |
Non-destructive testing Industrial computed radiography with storage phosphor imaging plates Part 2: General principles for testing of metallic materials using X- rays and gamma rays |
|
DS DS/EN 1518 |
Non-destructive testing - Leak testing - Characterization of mass spectrometer leak detectors |
|
DS DS/EN 1593 |
Non-destructive testing - Leak testing - Bubble emission techniques |
|
DS DS/EN 1593/A1 |
Non-destructive testing - Leak testing - Bubble emission techniques-(AMENDS DS/EN 1593) |
|
DS DS/EN 1779 |
Non-destructive testing - Leak testing - Criteria for method and technique selection |
|
DS DS/EN 1779/A1 |
Non-destructive testing - Leak testing - Criteria for method and technique selection-(AMENDS DS/EN 1779) |
|
DS DS/EN 25580 |
Non-destructive testing. Industrial radiographic illuminators. Minimum requirements |
|
DS DS/EN 45002 |
General criteria for the assessment of testing laboratories |
|
DS DS/EN 462- 1 |
Non-destructive testing - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value |
|
DS DS/EN 462- 2 |
Non destructive testing - Image quality of radiographs (step/hole type) - Determination of image quality value |
|
DS DS/EN 462- 3 |
Non-destructive testing - Image quality of radiographs - Part 3: Image quality classes for ferrous metals |
|
DS DS/EN 462- 4 |
Non destructive testing - Image quality of radiographs - Part 4: Experimental evaluation of image quality values and image quality tables |
|
DS DS/EN 462- 5 |
Non-destructive testing - Image quality of radiographs - Part 5: Image quality indicators (duplex wire type), determination of image unsharpness value |
|
DS DS/EN 473 |
Non-destructive testing - Qualification and certification of NDT personnel - General principles-Amendment 1: 11/03/2005 |
|
DS DS/EN 50104 |
Electrical apparatus for the detection and measurement of oxygen - Performance requirements and test methods |
|
DS DS/EN 50104 |
Electrical apparatus for the detection and measurement of oxygen - Performance requirements and test methods |
|
DS DS/EN 50104/A1 |
Electrical apparatus for the detection and measurement of oxygen - Performance requirements and test methods-(AMENDS DS/EN 50104) |
|
DS DS/EN 50191 |
Erection and operation of electrical test equipment |
|
DS DS/EN 50271 |
Electrical apparatus for the detection and measurement of combustible gases, toxic gases or oxygen - Requirements and tests for apparatus using software and/or digital technologies |
|
DS DS/EN 571- 1 |
Non destructive testing - Penetrant testing - Part 1: General principles |
|
DS DS/EN 583- 1 |
Non-destructive testing - Ultrasonic examination - Part 1: General principles |
|
DS DS/EN 583- 1/A1 |
Non-destructive testing - Ultrasonic examination - Part 1: General principles-(AMENDS DS/EN 583-1) |
|
DS DS/EN 583- 2 |
Non-destructive testing - Ultrasonic examination - Part 2: Sensitivity and range setting |
|
DS DS/EN 583- 3 |
Non destructive testing - Ultrasonic examination - Part 3: Transmission technique |
|
DS DS/EN 583- 4 |
Non-destructive testing - Ultrasonic examination - Part 4: Examination for discontinuities perpendicular to the surface |
|
DS DS/EN 583- 4/A1 |
Non-destructive testing - Ultrasonic examination - Part 4: Examination for discontinuities perpendicular to the surface-(AMENDS DS/EN 583-4) |
|
DS DS/EN 583- 5 |
Non-destructive testing - Ultrasonic examination - Part 5: Characterization and sizing of discontinuities |
|
DS DS/EN 583- 5/A1 |
Non-destructive testing - Ultrasonic examination - Part 5: Characterization and sizing of discontinuities-(AMENDS DS/EN 583-5) |
|
DS DS/EN 60052 |
Voltage measurement by means of standard air gaps |
|
DS DS/EN 60060- 2/A11 |
High-voltage test techniques - Part 2: Measuring systems-(AMENDS DS/EN 60060-2) |
|
DS DS/EN 60068- 1 |
Environmental testing - Part 1: General and guidance |
|
DS DS/EN 60068-2- 1+A1,2 |
Environmental testing - Part 2: Tests - Tests A: Cold |
|
DS DS/EN 60068-2- 11 |
Environmental testing - Part 2: Tests - Test Ka: Salt mist |
|
DS DS/EN 60068-2- 13 |
Environmental testing - Part 2: Tests - Test M: Low air pressure |
|
DS DS/EN 60068-2- 14 |
Environmental testing - Part 2: Tests - Test N: Change of temperature |
|
DS DS/EN 60068-2- 17 |
Basic environmental testing procedures - Part 2: Tests - Test Q: Sealing |
|
DS DS/EN 60068-2- 18 |
Environmental testing - Part 2-18: Tests - Tests R and guidance: Water |
|
DS DS/EN 60068-2- 2+A1,2 |
Basic environmental testing procedures - Part 2: Tests - Tests B: Dry heat |
|
DS DS/EN 60068-2- 21 |
Environmental testing - Part 2: Test - Test U: Robustness of terminations and integral mounting devices |
|
DS DS/EN 60068-2- 27 |
Basic environmental testing procedures - Part 2: Tests - Test Ea and guidance: Shock |
|
DS DS/EN 60068-2- 29 |
Basic environmental testing procedures - Part 2: Tests - Test Eb and guidance: Bump |
|
DS DS/EN 60068-2- 30 |
Environmental testing - Part 2: Tests - Test Db and guidance: Damp heat, cyclic (12 + 12 hour cycle) |
|
DS DS/EN 60068-2- 31 |
Basic environmental testing procedures - Part 2: Tests - Test Ec: Drop and topple, primarily for equipment-type specimens |
|
DS DS/EN 60068-2- 32 |
Basic environmental testing procedures - Part 2: Tests - Test Ed: Free fall |
|
DS DS/EN 60068-2- 33 |
Environmental testing - Part 2: Tests - Guidance on change of temperature tests |
|
DS DS/EN 60068-2- 38 |
Environmental testing - Part 2: Tests - Test Z/AD: Composite temperature/humidity cyclic test |
|
DS DS/EN 60068-2- 39 |
Environmental testing - Part 2: Tests - Test Z/AMD: Combined sequential cold, low air pressure and damp heat test |
|
DS DS/EN 60068-2- 40 |
Environmental testing - Part 2: Tests - Test Z/AM: Combined cold/low air pressure tests |
|
DS DS/EN 60068-2- 41 |
Environmental testing - Part 2: Tests - Test Z/BM: Combined dry heat/low air pressure tests |
|
DS DS/EN 60068-2- 42 |
Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
|
DS DS/EN 60068-2- 43 |
Environmental testing - Part 2-43: Tests - Test Kd: Hydrogen sulphide test for contacts and connections |
|
DS DS/EN 60068-2- 44 |
Environmental testing - Part 2: Tests - Guidance on Test T: Soldering |
|
DS DS/EN 60068-2- 45+A1 |
Basic Safety Publication - Environmental testing - Part 2: Test methods - Test XA and guidance: Immersion in cleaning solvents |
|
DS DS/EN 60068-2- 47 |
Environmental testing - Part 2-47: Test methods - Mounting of components, equipment and other articles for vibration, impact and similar dynamic tests |
|
DS DS/EN 60068-2- 48 |
Basic environmental testing procedures - Part 2: Tests - Guidance on the application of the tests of IEC Publication 68 to simulate the effects of storage |
|
DS DS/EN 60068-2- 5 |
Environmental testing - Part 2: Tests - Test Sa: Simulated solar radiation at ground level |
|
DS DS/EN 60068-2- 50 |
Basic environmental testing procedures - Part 2: Tests - Tests Z/AFc: Combined cold/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens |
|
DS DS/EN 60068-2- 51 |
Environmental testing - Part 2: Tests - Tests Z/BFc: Combined dry heat/vibration (sinusoidal) tests for both heat-dissipating and non-heat-dissipating specimens |
|
DS DS/EN 60068-2- 52 |
Environmental testing - Part 2: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution) |
|
DS DS/EN 60068-2- 57 |
Environmental testing - Part 2-57: Tests - Test Ff: Vibration - Time- history method |
|
DS DS/EN 60068-2- 58 |
Environmental testing Part 2-58: Tests Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
|
DS DS/EN 60068-2- 59 |
Environmental testing - Part 2: Test methods - Test Fe: Vibration - Sine beat method |
|
DS DS/EN 60068-2- 6 |
Environmental testing - Part 2: Tests - Tests Fc: Vibration (sinusoidal) |
|
DS DS/EN 60068-2- 60 |
Environmental testing - Part 2: Tests - Test Ke: Flowing mixed gas corrosion test |
|
DS DS/EN 60068-2- 61 |
Environmental testing - Part 2: Test methods - Test Z/ABDM: Climatic sequence |
|
DS DS/EN 60068-2- 62 |
Environmental testing - Part 2: Test methods - Test Ef: Impact, pendulum hammer |
|
DS DS/EN 60068-2- 64 |
Environmental testing - Part 2: Test methods - Test Fh: Vibration, broad- band random (digital control) and guidance |
|
DS DS/EN 60068-2- 66 |
Environmental testing - Part 2: Test methods - Test Cx: Damp heat, steady state (unsaturated pressurized vapour) |
|
DS DS/EN 60068-2- 67 |
Environmental testing - Part 2: Tests - Test Cy: Damp heat, steady state, accelerated test primarily intended for components |
|
DS DS/EN 60068-2- 68 |
Environmental testing - Part 2: Tests - Test L: Dust and sand |
|
DS DS/EN 60068-2- 69 |
Environmental testing - Part 2: Tests - Test Te: Solderability testing of electronic components for surface mount technology by the wetting balance method |
|
DS DS/EN 60068-2- 7 |
Basic environmental testing procedures - Part 2: Tests - Test Ga and guidance: Acceleration, steady state |
|
DS DS/EN 60068-2- 70 |
Environmental testing - Part 2: Tests - Test Xb: Abrasion of markings and letterings caused by rubbing of fingers and hands |
|
DS DS/EN 60068-2- 74 |
Environmental testing - Part 2: Tests - Test Xc: Fluid contamination |
|
DS DS/EN 60068-2- 75 |
Environmental testing - Part 2: Tests - Test Eh: Hammer tests |
|
DS DS/EN 60068-2- 77 |
Environmental testing - Part 2-77: Tests - Test 77: Body strength and impact shock |
|
DS DS/EN 60068-2- 78 |
Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
|
DS DS/EN 60068-2- 81 |
Environmental testing - Part 2-81: Tests - Test Ei: Shock - Shock response spectrum synthesis |
|
DS DS/EN 60068-2- 9 |
Environmental testing - Part 2: Tests - Guidance for solar radiation testing |
|
DS DS/EN 60068-3- 1 |
Environmental testing - Part 3: Background information - Section 1: Cold and dry heat tests |
|
DS DS/EN 60068-3- 2 |
Environmental testing - Part 3: Background information - Section 2: Combined temperature/low air pressure tests |
|
DS DS/EN 60068-3- 4 |
Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests |
|
DS DS/EN 60068-3- 5 |
Environmental testing - Part 3-5: Supporting documentation and guidance - Confirmation of the performance of temperature chambers |
|
DS DS/EN 60068-3- 6 |
Environmental testing - Part 3-6: Supporting documentation and guidance - Confirmation of the performance of temperature/humidity chambers |
|
DS DS/EN 60068-3- 8 |
Environmental testing - Part 3-8: Supporting documentation and guidance - Selecting amongst vibration tests |
|
DS DS/EN 60068-5- 2 |
Environmental testing - Part 5: Guide to drafting of test methods - Terms and definitions |
|
DS DS/EN 60270 |
High-voltage test techniques - Partial discharge measurements |
|
DS DS/EN 60721- 1+A2 |
Classification of environmental conditions - Part 1: Environmental parameters and their severities |
|
DS DS/EN 60721-3- 0 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Introduction |
|
DS DS/EN 60721-3- 1 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 1: Storage |
|
DS DS/EN 60721-3- 2 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation |
|
DS DS/EN 60721-3- 3 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weatherprotected locations |
|
DS DS/EN 60721-3- 3/A2 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 3: Stationary use at weatherprotected locations-(AMENDS DS/EN 60721-3-3) |
|
DS DS/EN 60721-3- 4+A1 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 4: Stationary use at non- weatherprotected locations |
|
DS DS/EN 60721-3- 5 |
Classification af environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 5: Ground vehicle installations |
|
DS DS/EN 60721-3- 6+A2 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 6: Ship environment |
|
DS DS/EN 60721-3- 7 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 7: Portable and non- stationary use |
|
DS DS/EN 60721-3- 7/A1 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 7: Portable and non- stationary use-(AMENDS DS/EN 60721-3-7) |
|
DS DS/EN 60721-3-9 + A1 |
Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 9: Microclimates inside products |
|
DS DS/EN 61010- 031 |
Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test |
|
DS DS/EN 61010- 1 |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
|
DS DS/EN 61010- 1/CORR. |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
|
DS DS/EN 61010- 1/CORR.1 |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
|
DS DS/EN 61010- 1/CORR.2 |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
|
DS DS/EN 61010-2- 032 |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-032: Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement |
|
DS DS/EN 61010-2- 081 |
Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic analytical equipment for analysis and other purposes |
|
DS DS/EN 61010-2- 081/A1 |
Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi- automatic laboratory equipment for analysis and other purposes-(AMENDS DS/EN 61010-2- 081) |
|
DS DS/EN 61028 |
Electrical measuring instruments - X-Y recorders |
|
DS DS/EN 61040 |
Power and energy measuring detectors, instruments and equipment for laser radiation |
|
DS DS/EN 61083- 1 |
Instruments and software used for measurements in high-voltage impulse tests - Part 1: Requirements for instruments |
|
DS DS/EN 61083- 2 |
Digital recorders for measurements in high-voltage impulse tests - Part 2: Evaluation of software used for the determination of the parameters of impulse waveforms |
|
DS DS/EN 61187 |
Electrical and electronic measuring equipment - Documentation |
|
DS DS/EN 61340-2- 1 |
Electrostatics - Part 2-1: Measurement methods - Ability of materials and products to dissipate static electric charge |
|
DS DS/EN 61340-2- 3 |
Electrostatics - Part 2-3: Methods of test for determining the resistance and resistivity of solid planar materials used to avoid electrostatic charge accumulation |
|
DS DS/EN 61557- 3 |
Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance |
|
DS DS/EN 61557- 4 |
Electrical safety in low voltage distribution systems up to 1000 V a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 4: Resistance of earth connection and equipotential bonding |
|
DS DS/EN 61557- 5 |
Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 5: Resistance to earth |
|
DS DS/EN 61557- 7 |
Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence |
|
DS DS/EN 61557- 8 |
Electrical safety in low voltage distribution systems up to 1 kV a.c. and 1,5 kV d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems |
|
DS DS/EN 933- 2 |
Tests for geometrical properties of aggregates - Part 2: Determination of particle size distribution - Test sieves, nominal size of apertures |
|
DS DS/EN ISO 12706 |
Non-destructive testing - Terminology - Terms used in penetrant testing |
|
DS DS/EN ISO 3059 |
Non-destructive testing - Penetrant testing and magnetic particle testing - Viewing conditions |
|
DS DS/EN ISO 3452- 2 |
Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials |
|
DS DS/EN ISO 3452- 3 |
Non-destructive testing - Penetrant testing - Part 3: Reference test blocks |
|
DS DS/EN ISO 3452- 4 |
Non-destructive testing - Penetrant testing - Part 4: Equipment |
|
DS DS/EN ISO 9934- 1 |
Non-destructive testing - Magnetic particle testing - Part 1: General principles |
|
DS DS/EN ISO 9934- 1/A1 |
Non-destructive testing - Magnetic particle testing - Part 1: General principles-(AMENDS DS/EN ISO 9934-1) |
|
DS DS/EN ISO 9934- 2 |
Non-destructive testing - Magnetic particle testing - Part 2: Detection media |
|
DS DS/EN ISO 9934- 3 |
Non-destructive testing - Magnetic particle testing - Part 3: Equipment |
|
DS DS/ENV 583- 6 |
Non-destructive testing - Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a method for detection and sizing of discontinuities |
|
DS DS/HD 478.2.6 S1 |
Classification of environmental conditions - Part 2: Environmental conditions appearing in nature - Earthquake vibration and shock |
|
DS DS/IEC 68-2- 20 |
Basic environmental testing procedures - Part 2: Tests - Test T: Soldering |
|
DS DS/IEC 68-2- 3 |
Basic environmental testing procedures - Part 2: Tests - Test Ca: Damp heat, steady state with Amendment No. 1 (1984) |
|
DS DS/IEC 68-2- 56 |
Environmental testing - Part 2: Tests - Test Cb: Damp heat, steady state, primarily for equipment |
|
DS DS/IEC 68-3- 3 |
Environmental testing - Part 3: Guidance - Seismic test methods for equipments |
|
DS DS/IEC 721-2- 1 |
Classification of evironmental conditions - Part 2: Environmental conditions appearing in nature - Temperature and humidity |
|
DS DS/IEC 721-2- 4 |
Classification of environmental conditions - Part 2: Environmental conditions appearing in nature - Solar radiation and temperature |
|
DS DS/IEC/TR 60721-4- 0 |
Classification of environmental conditions - Part 4-0: Guidance for the correlation and transformation of environmental condition classes of IEC 60721-3 to the environmental tests of IEC 60068 - Introduction |
|
DS DS/IEC/TR 61010- 3 |
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 3: Protocol for the preparation of conformity verification reports for the IEC 61010 2nd edition series |
|
DS DS/IEC/TR 61010-3- 031 |
Safety requirements for electrical equipment for measurement, control, and laboratory use Part 3-031: Conformity verification report for IEC 61010-031:2002 Safety requirements for hand-held probe assemblies for electrical test and measurement-(CD Rom) |
|
DS DS/INF 22/46 |
Comparative testing of consumer products and related services - General principles |
|
DS DS/ISO 1027 |
Radiographic image quality indicators for non-destructive testing - Principles and identification |
|
DS DS/ISO 3453 |
Non-destructive testing - Liquid penetrant inspection - Means of verification |